View MB89PV530C-201_6565703.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

fujitsu microelectronics data sheet copyright?2001-2008 fujitsu microelec tronics limited all rights reserved 2008.7 8-bit microcontroller cmos f 2 mc-8l mb89530a series mb89535a/537a/537ac/538a/538ac/f538 mb89p538/pv530 description the mb89530a series is a one-chip microcontroller featuring the f 2 mc-8l core supporting low-voltage and high- speed operation. built-in peripheral functions include timers, serial interface, a/d converter, and external interrupt. this product is an ideal general-purpose one-chip microcon troller for a wide variety of applications from household to industrial equipment, as well as use in portable devices. note : f 2 mc is the abbreviation of fuji tsu flexible microcontroller. features ? wide range of package options ? qfp package (1.00 mm pitch) ? two types of lqfp packages (0.65 mm pitch, 0.50 mm pitch) ? sh-dip package (1.778 mm pitch) ? bcc package (0.50 mm pitch) low voltage, high-speed operating capability minimum instruction execution time 0.32 s (at base oscillator 12.5 mhz) f 2 mc-8l cpu core ? instruction set optimized for controller operation ? multiplication/division instructions ? 16-bit calculation ? branching instructions with bit testing ? bit operation instructions, etc. (continued) ds07-12547-6e
mb89530a series 2 ds07-12547-6e (continued) five timer systems ? 8-bit pwm timer with 2 channels (usable as either interval timer of pwm timer) ? pulse width count timer (supports continuous meas urement or remote control receiving applications) ? 16-bit timer counter ? 21-bit time base timer ? watch prescaler (17-bit) uart synchronous or asynchro nous operation, switchable 2 serial interfaces (serial i/o) selection of transfer direction (speci fy msb first or lsb first) for communication with a variety of devices 10-bit a/d converter (8 channels) ? external clock input for startup support ? time base timer output for startup support (except mb89f538) pulse generators (ppg) with 2-program capability ? 6-bit ppg with selection of pulse width and pulse period ? 12-bit ppg (2 channels) with sele ction of pulse width and pulse period i 2 c* interface circuits external interrupt 1 (single-clock system : 4 channels, dual-clock system : 3 channels) 4 or 3 independent inputs, release enabled from standby mode (includes edge detection function) external interrupt 2 (except for mb89f5 38 : 8 channels, mb89f538 : 7 channels) 8 or 7 independent input, release enabled form st andby mode (includes level edge detection function) standby modes (low powe r consumption modes) ? stop mode (oscillator stops, virtually no power consumed) ? sleep mode (cpu stops, power consumption reduced to one-third) ? sub clock mode ? watch mode watchdog timer reset i/o ports ? maximum ports single-clock system : except mb89f538 53 ports : mb89f538 52 ports dual-clock system : except mb89f538 51 ports : mb89f538 50 ports ? 38 general-purpose i/o ports (cmos) (m b89f538 : 37 general-purpose i/o ports) ? 2 general-purpose i/o ports (n-ch open drain) ? 8 general-purpose output ports (n-ch open drain) ? general-purpose input ports (cmos) : single-c lock system : 5 ports, dual-clock system : 3 ports * : purchase of fujitsu i 2 c components conveys a lic ense under the philips i 2 c patent rights to use, these components in an i 2 c system provided that the system conforms to the i 2 c standard specification as defined by philips.
mb89530a series ds07-12547-6e 3 product lineup (continued) part number parameter mb89535a mb89537a/ 537ac mb89538a/ 538ac mb89f538 mb89p538 mb89pv530 type mass produced (mask rom) flash product one-time programmable product evaluation product rom capacity 16 kbytes 8-bit (built-in rom) 32 kbytes 8-bit (built-in rom) 48 kbytes 8-bit (built-in rom) 48 kbytes 8-bit (built-in flash) (write from general purpose eprom writer) 48 kbytes 8-bit (built-in rom) (write from general purpose eprom writer) 48 kbytes 8-bit (external rom) * 2 ram capacity 512 bytes 8-bit 1 kbyte 8-bit 2 kbytes 8-bit operating voltage 2.2 v to 5.5 v * 1 (mb89535a/537a/538a/537ac/538ac) 3.5 v to 5.5 v 2.7 v to 5.5 v 2.7 v to 5.5 v cpu functions basic instructions : 136 instruction bit length : 8 bits instruction length : 1 bit to 3 bits data bit length : 1, 8, 16 bits minimum instruction execution time : 0.32 s / 12.5 mhz minimum interrupt processing time : 2.88 s / 12.5 mhz peripheral functions ports input ports : single-clock system : 5 (4 also usable as external interrupts) dual-clock system : 3 (3 al so usable as external interrupts) output-only ports (n-ch open drain) : 8 (8 also usable as a/d converter input) i/o ports (n-ch open drain) : 2 (2 also usable as so2/sda or si2/scl) i/o ports (cmos) (except mb89f538) : 38 i/o ports (cmos) (mb89f538) : 37 (21 have no other function) total (except mb89f538) : single-clock system : 53 dual-clock system : 51 total (mb89f538) : single-clock system : 52 dual-clock system : 50 time base timer 21 bits interrupt periods at main clock oscillation frequency of 12.5 mhz (approx. 0.655 ms, 2.621 ms, 20.97 ms, 335.5 ms) watchdog timer reset period of approx. 167.8 ms to 335.6 ms at main clock frequency of 12.5 mhz reset period of approx. 500 ms to 1000 ms at sub clock frequency of 32.768 khz. pwm timer 8-bit interval timer operation (supports square wave output, oper ating clock period : 1, 8, 16, 64 t inst * 3 ) pulse width measurement with 8-bit resolution (conversion period : 2 8 t inst * 3 to 2 8 64 t inst * 3 ) 2 channels (can also be used as in terval timer, can also be used as ch.1 output and ch.2 count clock) watch prescaler interval times at 17-bit sub cl ock base frequency of 32.768 khz (approx. 31.25 ms, 0.25 s, 0. 50 s, 1.00 s, 2.00 s, 4.00 s)
mb89530a series 4 ds07-12547-6e (continued) *1 : depends on operating frequency. *2 : using external rom and mbm27c512. *3 : t inst represents instruction execution time. this can be select ed as 1/4, 1/8, 1/16, 1/64 of the main clock cycle or 1/2 of the sub clock cycle. note : mb89535a/537a/538a have no built-in i 2 c functions. to use i 2 c functions, choose the mb89pv 530/mb89p538/f538/537ac/538ac. part number parameter mb89535a mb89537a/ 537ac mb89538a/ 538ac mb89f538 mb89p538 mb89pv530 peripheral functions pulse width count timer 8-bit one-shot timer operation (supports underflow output, operating clock period : 1, 4, 32 t inst * 3 , external) 8-bit reload timer operation (supports square wave output, oper ating clock period : 1, 4, 32 t inst * 3 , external) 8-bit pulse width measurement operation (continuous measurement, ?h? width measurement, ?l? width measurement, to , to , ?h? width measurement and to ) 16-bit timer/ counter 16-bit timer operation (operating clock period : 1 t inst * 3 , external) 16-bit event counter operation (sel ect rising, falling, or both edges) 16-bit 1 channel serial i/o 8 bits length selection of lsb first or msb first transfer clock (2, 8, 32 t inst * 3 , external) uart/sio clk synchronous/clk asynchronous data transfer c apability (8, 9-bit with parity bit, or 7,8-bit without parity bit) . built-in baud rate generator provides selection of 14 baud rate settings. uart clk synchronous/clk asynchronous data transfer cap ability (4, 6, 7, 8-bit with parity bit, or 5, 7, 8, 9-bit without parity bit) . built-in baud rate generator provides selection of 14 baud rate settings. external clock output, 2-channel 8-bit pwm timer output also available for baud rate settings. external interrupt 1 single-clock system : 4 cha nnels independent, dual-clock sy stem : 3 channels independent. selection of rising, fallin g, or both edge detection. can be used for recovery from standby mode (e dge detection also available in stop mode) external interrupt 2 except mb89f538 : 8 chan nels, mb89f538 : 7 channels can be used for recovery from standby mode. 6-bit ppg, 12-bit ppg can generate square wave sign als with programmable period. 6-bit 1 channel or 12-bit 2 channels. i 2 c bus interface ? 1-channel , compatible with intel system administrator bus version 1.0 and philips i 2 c specifications. 2-line communications ( on mb89pv530 / p538 / f538/537ac / 538ac ) a/d converter 10-bit resolution 8 channels. a/d conversion functions (conversion time : 60 t inst * 3 ) supports repeated calls from ex ternal clock (except mb89f538) . supports repeated calls from internal clock. standard voltage input provided (avr) standby modes (power saving modes) sleep mode, stop mode, su b clock mode, watch mode. process cmos
mb89530a series ds07-12547-6e 5 model differences and selection considerations : model-package combination available : model-package combination not available * : only for es conversion sockets for pin pitch conversion (m anufactured by sunhayato corp.) can be used. contact : sunhayato corp. : tel : + 81-3-3984-7791 fax : + 81-3-3971-0535 advanced interconnectics : http:// www.advantest.co.jp/en-index.shtml part number package mb89535a mb89537a/ 537ac mb89538a/ 538ac mb89f538 mb89p538 mb89pv530 dip-64p-m01 fpt-64p-m03 fpt-64p-m06 fpt-64p-m09 lcc-64p-m19 lcc-64p-m16 * mdp-64c-p02 mqp-64c-p01
mb89530a series 6 ds07-12547-6e differences among products 1. memory capacity when this product is used in an evaluation product or othe r evaluation configuration, it is necessary to carefully confirm the differences between the model being used and the product it is evaluating. particular attention should be given to the following (refer to ? cpu core 1.memory space?) . the program rom area starts from address 4000 h on the mb89f538, mb89p538 and mb89pv530 models. note upper limits on ram, such as stack areas, etc. 2. current consumption on the mb89pv530, the additional cu rrent consumed by the eprom is added at the connecting socket on the back side. when operating at low speed, the cu rrent consumption in the one-time pr om or eprom models is greater than on the mask rom models. however, current c onsumption in sleep or st op modes is identical. for details, refer to ? electrical characteristics?. 3. mask options the options available for use, and the method of specifying options, differ according to the model. before use, check the ? mask options? specification section. 4. wild register functions the following table shows areas in which wild register functions can be used. wild register usage areas part number address space mb89pv530 4000 h to ffff h mb89p538 4000 h to ffff h mb89f538 4000 h to ffff h mb89537a/537ac 8000 h to ffff h mb89538a/538ac 4000 h to ffff h mb89535a c000 h to ffff h
mb89530a series ds07-12547-6e 7 pin assignments (continued) (top view) (dip-64p-m01) (mdp-64c-p02) *1 : pin 10 is mod2 pin for mb89f538 and p47/int27/adst pins except for mb89f538. *2 : pin 25 and pin 26 are p63/int13, p64 pins for si ngle-clock system and x0a, x1a pins for dual-clock system. *3 : the function of pin 57 depends on the model. for details, refer to ? pin descriptions? and ? handling devices?. *4 : package top pin assignments (mb89pv530 only) n.c. : internal connection only. not for use. pin no. pin name pin no. pin name pin no. pin name pin no. pin name 65a1573a181o689a8 66a1274a082o790a13 67 a7 75 o1 83 o8 91 a14 68 a6 76 o2 84 ce 92 v cc 69 a5 77 o3 85 a10 70 a4 78 v ss 86 oe 71 a3 79 o4 87 a11 72 a2 80 o5 88 a9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 p36/wto p37/pto1 p40/int20/ec p41/int21/sck2 p42/int22/so2/sda p43/int23/si2/scl p44/int24/uck2 p45/int25/uo2 p46/int26/ui2 p47/int27/adst/mod2* 1 p50/an0 p51/an1 p52/an2 p53/an3 p54/an4 p55/an5 p56/an6 p57/an7 av cc avr av ss p60/int10 p61/int11 p62/int12 p63/int13/x0a* 2 p64/x1a* 2 rst mod0 mod1 x0 x1 v ss 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 v cc p35/pwc p34/pto2 p33/si1 (ui1) p32/so1 (uo1) p31/sck1 (uck1) /lmco p30/ppg03/mco c/n.c. * 3 p00 p01 p02 p03 p04 p05 p06 p07 p10 p11 p12 p13 p14 p15 p16 p17 p20/pwck p21/ppg01 p22/ppg02 p23 p24 p25 p26 p27 92 91 90 89 88 87 86 85 84 83 82 81 80 79 65 66 67 68 69 70 71 72 73 74 75 76 77 78 v cc a14 a13 a8 a9 a11 oe a10 ce o8 o7 o6 o5 o4 a15 a12 a7 a6 a5 a4 a3 a2 a1 a0 o1 o2 o3 v ss * 4
mb89530a series 8 ds07-12547-6e (continued) (top view) (fpt-64p-m03) (fpt-64p-m09) *1 : pin 2 is mod2 pin for mb89f538 and p47/int27/adst pins except for mb89f538. *2 : pin 17 and pin 18 are p63/int13, p64 pins for single-clock system and x0a, x1a pins for dual-clock system. *3 : the function of pin 49 depends on the model. for details, refer to ? pin descriptions? and ? handling devices?. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 p46/int26/ui2 p47/int27/adst/mod2* 1 p50/an0 p51/an1 p52/an2 p53/an3 p54/an4 p55/an5 p56/an6 p57/an7 av cc avr av ss p60/int10 p61/int11 p62/int12 p00 p01 p02 p03 p04 p05 p06 p07 p10 p11 p12 p13 p14 p15 p16 p17 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 p63/int13/x0a* 2 p64/x1a* 2 rst mod0 mod1 x0 x1 v ss p27 p26 p25 p24 p23 p22/ppg02 p21/ppg01 p20/pwck p45/int25/uo2 p44/int24/uck2 p43/int23/si2/scl p42/int22/so2/sda p41/int21/sck2 p40/int20/ec p37/pto1 p36/wto v cc p35/pwc p34/pto2 p33/si1 (ui1) p32/so1 (uo1) p31/sck1 (uck1) /lmco p30/ppg03/mco c/n.c.* 3
mb89530a series ds07-12547-6e 9 (continued) (top view) (fpt-64p-m06) (mqp-64c-p01) *1 : pin 3 is mod2 pin for mb89f538 and p47/int27/adst pins except for mb89f538. *2 : pin 18 and pin 19 are p63/int13, p64 pins for si ngle-clock system and x0a, x1a pins for dual-clock system. *3 : the function of pin 50 depends on the model. for details, refer to ? pin descriptions? and ? handling devices?. *4 : package top pin assignments (mb89pv530 only) n.c. : internal connection only. not for use. pin no. pin name pin no. pin name pin no. pin name pin no. pin name 65 n.c. 73 a2 81 n.c. 89 oe 66a1574a182o490n.c. 67a1275a083o591a11 68 a7 76 n.c. 84 o6 92 a9 69 a6 77 o1 85 o7 93 a8 70 a5 78 o2 86 o8 94 a13 71 a4 79 o3 87 ce 95 a14 72 a3 80 v ss 88 a10 96 v cc 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 p30/ppg03/mco c/n.c. p00 p01 p02 p03 p04 p05 p06 p07 p10 p11 p12 p13 p14 p15 p16 p17 p20/pwck 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 p45/int25/uo2 p46/int26/ui2 p47/int27/adst/mod2* 1 p50/an0 p51/an1 p52/an2 p53/an3 p54/an4 p55/an5 p56/an6 p57/an7 av cc avr av ss p60/int10 p61/int11 p62/int12 p63/int13/x0a* 2 p64/x1a* 2 64 63 62 61 60 59 58 57 56 55 54 53 52 rst mod0 mod1 x0 x1 v ss p27 p26 p25 p24 p23 p22/ppg02 p21/ppg01 94 95 96 65 66 67 68 84 83 82 81 80 79 78 20 21 22 23 24 25 26 27 28 29 30 31 32 p44/int24/uck2 p43/int23/si2/scl p42/int22/so2/sda p41/int21/sck2 p40/int20/ec p37/pto1 p36/wto v cc p35/pwc p34/pto2 p33/si1 (ui1) p32/so1/ (uo1) p31/sck1 (uck1) /lmco 85 86 87 88 89 90 91 92 93 77 76 75 74 73 72 71 70 69 * 4 * 3
mb89530a series 10 ds07-12547-6e (continued) (top view) (lcc-64p-m19) (lcc-64p-m16) * 4 *1 : pin 2 is mod2 pin for mb89f538 and p47/int27/adst pins except for mb89f538. *2 : pin 17 and 18 are p63/int13, p64 pins for single- clock system and x0a, x1a pins for dual-clock system. *3 : the function of pin 49 depends on the model. for details, refer to ? pin descriptions? and ? handling devices?. *4 : only for es 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 p46/int26/ui2 p47/int27/adst/mod2 ? 1 p50/an0 p51/an1 p52/an2 p53/an3 p54/an4 p55/an5 p56/an6 p57/an7 av cc avr av ss p60/int10 p61/int11 p62/int12 p00 p01 p02 p03 p04 p05 p06 p07 p10 p11 p12 p13 p14 p15 p16 p17 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 p63/int13/x0a ? 2 p64/x1a ? 2 rst mod0 mod1 x0 x1 v ss p27 p26 p25 p24 p23 p22/ppg02 p21/ppg01 p20/pwck p45/int25/uo2 p44/int24/uck2 p43/int23/si2/scl p42/int22/so2/sda p41/int21/sck2 p40/int20/ec p37/pto1 p36/wto v cc p35/pwc p34/pto2 p33/si1 (ui1) p32/so1 (uo1) p31/sck1 (uck1) /lmco p30/ppg03/mco c/nc ? 3
mb89530a series ds07-12547-6e 11 pin descriptions (continued) pin no. pin name i/o circuit type* 7 function sh-dip* 1 mdip* 2 qfp* 3 mqfp* 4 lqfp* 5 bcc* 6 30 23 22 x0 a connecting pins to crystal oscillator circuit or other oscillator circuit. the x0 pin can connect to an external clock. in that case, x1 is left open. 31 24 23 x1 28 21 20 mod0 b input pins for memory access mode setting. connect directly to vss. 29 22 21 mod1 27 20 19 rst c reset i/o pin. this pin has pull-up resistance with cmos i/o or hysteresis input. at an internal reset request, an ?l? signal is ou tput. an ?l? level input initializes the internal circuits. 56 to 49 49 to 42 48 to 41 p00 to p07 d general purpose i/o ports. 48 to 41 41 to 34 40 to 33 p10 to p17 d general purpose i/o ports. 40 33 32 p20/pwck e general purpose i/o port.resource i/o pin (hysteresis input).hysteresis input. this pin also functions as a pwc input. 39 32 31 p21/ ppg01 d general purpose i/o port.this pin also functions as the ppg01 output. 38 31 30 p22/ ppg02 d general purpose i/o port.this pin also functions as the ppg02 output. 37 30 29 p23 d general purpose i/o port. 36 29 28 p24 d general purpose i/o port. 35 28 27 p25 d general purpose i/o port. 34 27 26 p26 d general purpose i/o port. 33 26 25 p27 d general purpose i/o port. 58 51 50 p30/ ppg03/ mco d general purpose i/o port.this pin also functions as the ppg03 output. 59 52 51 p31/sck1 (uck1) / lmco e general purpose i/o port.resource i/o pin (hysteresis input).this pin also functions as the uart/sio clock input/output pin. 60 53 52 p32/so1 (uo1) d general purpose i/o port.this pin also functions as the uart/sio data output pin. 61 54 53 p33/si1 (ui1) e general purpose i/o port.resource input/output pin (hysteresis input).this pin also functions as the uart/ sio serial data input pin. 62 55 54 p34/pto2 d general purpose i/o port.this pin also functions as the pwm timer 2 output pin. 63 56 55 p35/pwc e general purpose i/o port.resource i/o pin (hysteresis input).this pin also functions as a pwc input.
mb89530a series 12 ds07-12547-6e (continued) pin no. pin name i/o circuit type* 7 function sh-dip* 1 mdip* 2 qfp* 3 mqfp* 4 lqfp* 5 bcc* 6 15857 p36/ wto d general purpose i/o port.resource output. this pin also functions as the pwc output pin. 25958 p37/ pto1 d general purpose i/o port.resource output. this pin also functions as the pwm timer 1 output pin. 36059 p40/ int20/ ec e general purpose i/o port.resource i/o pin (hysteresis input).this pin also functions as an external interrupt input or 16-bit timer/counter input. 46160 p41/ int21/ sck2 e general purpose i/o port.resource i/o pin (hysteresis input).this pin also functions as an external interrupt input or sio clock i/o pin. 56261 p42/ int22/ so2/ sda g n-ch open drain output. resource i/o pin (hysteresis only for int22 input) . this pin also functions as an external interrupt input, sio serial data output, or i 2 c data line. 66362 p43/ int23/ si2/scl g n-ch open drain output. resource i/o pin (hysteresis only for int23 input) . this pin also functions as an external interrupt, sio serial data input, or i 2 c clock i/o pin. 76463 p44/ int24/ uck2 e general purpose i/o port. resource i/o pin (hysteresis input) . this pin also functions as an external interrupt input or uart clock i/o pin. 8164 p45/ int25/ uo2 e general purpose i/o port. resource i/o pin (hysteresis input) . this pin also functions as an external interrupt input or uart data output pin. 921 p46/ int26/ ui2 e general purpose i/o port. resource i/o pin (hysteresis input) . this pin also functions as an external interrupt input or uart data input pin. 10 3 2 p47/ int27/ adst e except mb89f538 general purpose i/o port. resource i/o pin (hysteresis input) . this pin also functions as an external interrupt input or a/d converter clock input pin. mb89f538 input pins for memory access mode setting. connect directly to vss. mod2 b 11 to 18 4 to 11 3 to 10 p50/an0 to p57/ an7 h n-ch open drain output port. this pin also functions as an a/d converter analog input pin.
mb89530a series ds07-12547-6e 13 (continued) *1 : dip-64p-m01 *2 : mdp-64c-p02 *3 : fpt-64p-m06 *4 : mqp-64c-p01 *5 : fpt-64p-m03/m09 *6 : lcc-64p-m19/m16 *7 : for i/o circuit type, refer to ? i/o circuit type? . pin no. pin name i/o circuit type* 7 function sh-dip* 1 mdip* 2 qfp* 3 mqfp* 4 lqfp* 5 bcc* 6 22 to 24 15 to 17 14 to 16 p60/int10 to p62/int12 i general purpose input port. resource input pin (hysteresis input) . this pin also functions as an external interrupt input pin. 25 18 17 p63/int13 i single-clock system general purpose input port. resource input (hysteresis input) . this pin also functions as an external interrupt. x0a a dual-clock system co nnected pin for sub clock. 26 19 18 p64 j single-clock system general purpose input port. x1a a dual-clock system co nnected pin for sub clock. 64 57 56 v cc ? power supply pin. 32 25 24 v ss ? ground pin (gnd) . 19 12 11 av cc ? a/d converter power supply pin. 20 13 12 avr ? a/d converter reference voltage input pin. 21 14 13 av ss ? a/d converter power supply pin. used at the same voltage level as the vss supply. 57 50 49 c ? mb89f538 capacitor connection pin for stabilization power supply. connect an external ceramic capacitor of approximately 0.1 f. mb89p538 if ?available? is selected for the step-down circuit stabilization time, v cc is fixed. if ?unavailable? is selected for the step-down circuit stabilization time, v ss is fixed. mb89pv530 mb89537a/537ac mb89538a/538ac mb89535a n.c. pin
mb89530a series 14 ds07-12547-6e external eprom socket pin function descriptions (mb89pv530 only) *1 : mdp-64c-p02 *2 : mqp-64c-p01 *3 : for i/o circuit type, refer to ? i/o circuit type? . pin no. pin name i/o circuit type* 3 function mdip* 1 mqfp* 2 65 66 67 68 69 70 71 72 73 74 66 67 68 69 70 71 72 73 74 75 a15 a12 a7 a6 a5 a4 a3 a2 a1 a0 o address output pins. 75 76 77 77 78 79 o1 o2 o3 i data input pins 78 80 v ss o power supply pin (gnd) . 79 80 81 82 83 82 83 84 85 86 o4 o5 o6 o7 o8 i data input pins. 84 87 ce o rom chip enable pin. outputs an ?h? level signal in standby mode. 85 88 a10 o address output pin. 86 89 oe o rom output enable pin. outputs ?l? at all times. 87 88 89 91 92 93 a11 a9 a8 o address output pins. 90 94 a13 o 91 95 a14 o 92 96 v cc o eprom power supply pin. ? 65 76 81 90 n.c. o internally connected. these pins always left open.
mb89530a series ds07-12547-6e 15 i/o circuit types (continued) type circuit remarks a oscillator feedback resistance high speed side = approx. 1 m ? low speed side = approx. 10 m ? b hysteresis input pull-down resistance built-in to mb89535a mb89537a/537ac mb89538a/538ac c pull-up resistance approx. 50 k ? hysteresis input d cmos i/o software pull-up resistance can be used. approx. 50 k ? e cmos i/o software pull-up resistance can be used. approx. 50 k ? n-ch n-ch x1 (x1a) x0 (x0a) p-ch p-ch clock input standby control r mode input r p-ch n-ch reset output reset input p-ch p-ch n-ch r pull-up control resistor digital output digital output port input p-ch p-ch n-ch r pull-up control resistors port input resource input digital output digital output
mb89530a series 16 ds07-12547-6e (continued) type circuit remarks g n-ch open drain output hysteresis input cmos input h n-ch open drain output analog input (a/d converter) i hysteresis input cmos input software pull-up resistance can be used. approx. 50 k ? j cmos input software pull-up resistance can be used. approx. 50 k ? n-ch resource input port input digital output n-ch p-ch analog input digital output p-ch r pull-up control resistors port resource p-ch r pull-up control resistors port
mb89530a series ds07-12547-6e 17 handling devices 1. preventing latch-up care must be taken to ensure that maximum voltage ratings are not exceeded (to prevent latch-up) . when cmos integrated circuit devices are subjected to applied voltages higher than vcc at input and output pins (other than medium- and high-withstand voltage pins), or to voltages lower than vs s, as well as when voltages in excess of rated levels are applied between vcc and vs s, the phenomenon known as latch-up can occur. when a latch-up condition occurs, supply current c an increase dramatically and may destroy semiconductor elements. in using semiconductor devices, always take sufficient care to avoid exceeding maximum ratings. also when switching power on or off to analog system s, care must be taken that analog power supplies (av cc , avr) and analog input signals do not exceed the level of the digital power supply. 2. power supply voltage fluctuations even within the warranted operating range of the vcc supply voltage, sudden changes in supply voltage can cause abnormal operation. as a measure for stability, it is recommended that the vcc ripple fluctuation (peak to peak value) should be kept within 10% of the reference vcc value on commercial power supply (50 hz/60 hz), and instantaneous voltage fluctuations such as at powe r-on and shutdown should be kept within a transient variability limit of 0.1v/ms. 3. treatment of unused input pins if unused input pins are left open, abnormal operation may result. any unus ed input pins should be connected to pull-up or pull-down resistance. 4. treatment of n.c. pins any pins marked ?nc? (not c onnected) must be left open. 5. treatment of power supply pins on models with built-in a/d converter even when a/d converters are not in use, pins should be connected so that av cc = v cc , and av ss = avr = v ss . 6. precautions for use of external clock even when an external clock signal is used, an oscillato r stabilization wait period is used after a power-on reset, or escape from sub clock mode or stop mode. 7. execution of programs on ram debugging of programs executed on ram c annot be performed even when using the mb89pv530. 8. wild register functions wild registers cannot be debugged with the mb89pv530 and tools. to verify o perations, actual in-device testing on the mb89p538 or mb89f538 is advised.
mb89530a series 18 ds07-12547-6e 9. details on handling the c terminal of the mb89530 series the mb89530 series contains the following products. the regulator integrated model and the regulator-less model have different performance characteristics. although these product models have the same internal resources, the operation sequence after a power-on reset is different between the regulator integrated model and regulator-less model. the operation sequence after a power-on reset of each model is shown below. as above, the regulator integrated model starts the cp u behind the regulator-less model. this is because the regulator requires a settling time for normal operation. the mb89p538 offers a choice of regulator-integrated and regulator-less models selectable depending on the c-terminal treatment. use the ri ght one for your mask board. 10. note to noise in th e external reset pin (rst ) if the reset pulse applied to the external reset pin (rst ) does not meet the specifications, it may cause malfunc- tions. use caution so that the reset pulse less than the s pecifications will not be fed to the external reset pin (rst ). part no. operation voltage integrated model terminal type terminal treatments mb89pv530 2.7 v to 5.5 v not included n.c. terminal not required mb89p538 included c terminal fixed to v cc not included fixed to v ss mb89f538 3.5 v to 5.5 v included 0.1 f capacitor connected mb89537a/537ac 2.2 v to 5.5 v not included n.c. terminal not required mb89538a/538ac mb89535a power supply (v cc ) cpu operation of regulator integrated model (mb89f538 only) cpu operation of regulator-less model (exclude mb89f538) voltage step-down circuit stabilization time + oscillation stabilization time (2 19 /f ch ) + ( 2 18 /f ch ) oscillation stabiliza- tion time (2 18 /f ch ) cpu started on regulator-less model (reset vector) cpu started on regulator integrated model (reset vector) f ch : crystal oscillator frequency
mb89530a series ds07-12547-6e 19 programming and erasing flash memory on the mb89f538 1. flash memory the flash memory is located between 4000 h and ffff h in the cpu memory map and incorporates a flash memory interface circuit that allows read access and pr ogram access from the cpu to be performed in the same way as mask rom. programming and erasing flash memory is also performed via the flash memory interface circuit by executing instructions in the cpu. this enables the flash memory to be updated in place under the control of the cpu, providing an effi cient method of updating program and data. 2. flash memory features 48 kbytes 8-bit configuration (16 kbytes + 8 kbytes + 8 kbytes + 16 kbytes sectors) automatic programming algorithm (embedded algorithm : equivalent to mbm29lv200) includes an erase pause and restart function data polling and toggle bit for detection of program/erase completion detection of program/erase completion via cpu interrupt compatible with jedec-standard commands sector protection (sectors can be combined in any combination) no. of program/erase cycles : 10,000 (min) 3. procedure for programming and erasing flash memory programming and reading flash memory cannot be perfor med at the same time. accordingly, to program or erase flash memory, the program must first be copied fr om flash memory to ram so that programming can be performed without program access from flash memory. 4. flash memory register flash memory control status register (fmcs) 5. sector configuration the table below shows the sector configuration of flash memory and lists the addresse s of each sector for both during cpu access a flash memory programming. sector configuration of flash memory * : programmer address the programmer address is the address to be used in stead of the cpu address when programming data from a parallel flash memory programmer. use the programmer address on programming or erasing using a general- purpose parallel programmer. flash memory cpu address programmer address* 16 kbytes ffff h to c000 h 1ffff h to 1c000 h 8 kbytes bfff h to a000 h 1bfff h to 1a000 h 8 kbytes 9fff h to 8000 h 19fff h to 18000 h 16 kbytes 7fff h to 4000 h 17fff h to 14000 h r r/w r/w rdy bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 007a h address 000x00-0 b initial value reserved reserved ? reserved r/w ? r/w r/w r/w inte rdyint we
mb89530a series 20 ds07-12547-6e 6. rom programmer adaptor and recommended rom programmers * : for the version of the programmer , contact the flash support group, inc. enquiries sunhayato corp. : tel : + 81-3-3984-7791 fax : + 81-3-3971-0535 advanced interconnectics : http://w ww.advantest.co.jp/en-index.shtml flash support group, inc. : fax : + 81-53-428-8377 e-mail : support@j-fsg.co.jp part number package adaptor part no. recommended programmer manufacturer and model sunhayato corp. flash support group, inc. mb89f538-101pf mb89f538-201pf fpt-64p-m06 flash-64qf-32dp-8lf af9708* af9709* mb89f538-101pfm mb89f538-201pfm fpt-64p-m09 flash-64qf2-32dp-8lf2 mb89f538-101p-sh mb89f538-201p-sh dip-64p-m01 flash-64sd-32dp-8lf
mb89530a series ds07-12547-6e 21 one-time writing specifications with prom and eprom microcontrollers the mb89p538 has a prom mode with functions equivalent to the mbm27c1001, allowing writing with a general purpose rom writer using a proprietary adapter. note, however, that the use of electronic signature mode is not supported. ? rom writer adapters with some rom writers, stability of writin g performance is enhanced by placing an 0.1 f capacitor between the vcc and vss pins. the following table lis ts adapters for use with rom writers. rom writer adapters inquiries should be addressed to sunhayato corp. : tel : + 81-3-3984-7791 fax : + 81-3-3971-0535 advanced interconnectics : http://www.advantest.co.jp/en-index.shtml *1 : version 3 or later should be used. *2 : only for es ? memory map for eprom mode the following illustration shows a memory ma p for eprom mode. there are no prom options. part number package compatible adapter mb89p538-101pf mb89p538-201pf fpt-64p-m06 rom-64qf-32dp-8la2* 1 mb89p538-101pfm mb89p538-201pfm fpt-64p-m09 rom-64qf2-32dp-8la mb89p538-101p-sh mb89p538-201p-sh dip-64p-m01 rom-64sd-32dp-8la2* 1 mb89p538-101pv mb89p538-201pv lcc-64p-m16* 2 rom-64bcc-32dp-8la-fj 4000 h ffff h 1ffff h 0000 h 0000 h ram rom i/o 0080 h 4000 h 0880 h ffff h 0200 h 0100 h general purpose register normal operating mode prohibited eprom mode (corresponding addresses on eprom writer) program (eprom) prohibited prohibited
mb89530a series 22 ds07-12547-6e ? recommended screening conditions before one-time writing of microcontroller programs to prom, high temperature aging is recommended as a screening process for chips before they are mounted. ? about writing yields the nature of chips before one-time writing of microcont roller programs to prom prevents the use of all-bit writing tests. therefore it is not possible to guarantee writing yields of 100% in some cases. program, verify high temperature aging + 150 c, 48h read mount
mb89530a series ds07-12547-6e 23 eprom writing to piggy-back/evaluation chips this section describes methods of writin g to eprom on piggy-back/evaluation chips. ? eprom model mbm27c512-20tv ? writer adapter for writing to eprom using a rom writer, use one of the writer adapters shown below (manufactured by sunhayato corp.) . inquiries should be addressed to sunhayato corp. : tel : + 81-3-3984-7791 fax : + 81-3-3971-0535 advanced interconnectics : http://www.advantest.co.jp/en-index.shtml ? memory space ? writing to eprom 1) set up the eprom writer for the mbm27c512. 2) load program data to the erpom writer, in the area 4000 h to ffff h . 3) use the eprom writer to write to the area 4000 h to ffff h . package adapter socket model lcc-32 (rectangular) rom-32lc-28dp-yg 4000 h ffff h 0000 h 0000 h ram prom 4 8 k b yte s eprom i/o 00 8 0 h 4000 h ffff h 0 88 0 h normal operating mode prohibited (corresponding address on rom writer) prohibited
mb89530a series 24 ds07-12547-6e block diagram 4 p6 3 /int1 3 /x0a * 1 p64/x1a * 1 p60/int10 to p62/int12 x0 x1 r s t p 3 0/ppg0 3 /mco p 3 2/ s o1 (uo1) p 3 4/pto2 p 3 5/pwc p 3 6/wto p 3 7/pto1 p 33 / s i1 (ui1) p 3 1/ s ck1 (uck1) /lmco f 2 mc- 8 l cpu mod0, mod1, mod2 * 2 , v cc , v ss , c/n.c. pwc uart/ s io 8 8 p00 to p07 p10 to p17 p20/pwck p21/ppg01 p22/ppg02 p40/int20/ec p41/int21/ s ck2 p44/int24/uck2 p45/int25/uo2 p46/int26/ui2 p47/int27/ad s t * 2 p50/an0 to p57/an7 av cc avr av ss p4 3 /int2 3 / s i2/ s cl p42/int22/ s o2/ s da p2 3 to p27 8 8 s io uart i 2 c rom (16 k b yte s / 3 2 k b yte s /4 8 k b yte s ) 8 - b it pwm timer 2 8 - b it pwm timer 1 sub clock main clock low voltage oscillator circuit (32.786 khz) clock control watch prescaler external interrupt 1 (edge) cmos i/o port oscillator circuit clock controller reset circuit ( watchdog timer ) 21-bit time base timer 6-bit ppf03 cmos i/o port ram (512 kbytes/1 kbyte/2 kbytes) wild register other pins cmos i/o port cmos i/o port 12-bit ppg01 12-bit ppg02 cmos i/o port 16-bit timer/ counter 1 external interrupt 2 (level) n-ch i/o cmos i/o port n-ch output 10-bit a/d converter port 6 port 0 port 1 port 2 port 4 port 3 port 5 internal data bus *1 : p63/int13, p64 pins for single-clock system and x0a, x1a pins dual-clock system *2 : p47/int27/adst pins are mod2 pin for mb89f538.
mb89530a series ds07-12547-6e 25 cpu core 1. memory space the mb89530a series has 64 kbytes of memory space, containing all i/o, data areas, and program areas. the i/o area is located at the lowest addresses, with th e data area placed immediately above. the data area can be partitioned into register areas, stack areas, or dire ct access areas depending on the application. the program area is located at the opposite end of memory, closest to the highest addresses, a nd the highest part of this area is assigned to the tables of interrupt and reset ve ctors and vector call instructions. the following diagram shows the structure of memory space in the mb89530a series. ? memory map 0000 h ram rom i/o 0080 h 0c80 h 0480 h ffff h 0200 h 0100 h 0c91 h 8000 h ffc0 h 0000 h ram mb89537a/537ac 0000 h ram rom i/o 0080 h 0c80 h 0280 h ffff h 0200 h 0100 h 0c91 h c000 h ffc0 h mb89535a mb89pv530 mb89p538/f538 mb89538a/538ac rom i/o 0080 h 0c80 h 0880 h ffff h 0200 h 0100 h 0c91 h 4000 h ffc0 h general purpose register general purpose register general purpose register open wild register open vector tables* 2 open wild register open vector tables* 2 *1 : the external rom ar ea is on the mb89pv530 only. *2 : vector tables (reset, interrupt, vector call instructions) external rom* 1 open wild register open vector tables* 2
mb89530a series 26 ds07-12547-6e 2. registers the f 2 mc-8l series has two types of registers, dedicated- use registers within the cpu, and general-purpose registers in memory. in addition, the ps register can be divided so that the upper 8 bits are used as a register bank pointer (rp), and the lower 8 bits as a condition code register (ccr). (refer to the following illustration.) program counter (pc) : 16-bit length, show s the location where instructions are stored. accumulator (a) : 16-bit length, a temporary memory register for calculation operations. the lower byte is used for 8-bit data processing instructions. temporary accumulator (t) : 16-bit length, performs calculations with the accumulator. the lower byte is used for 8-bit data processing instructions. index register (ix) : 16-bit length , a register for index modification. extra pointer (ep) : 16-bit length, a pointer indicating memory addresses. stack pointer (sp) : 16-bit length, indicates stack areas. program status (ps) : 16-bit length, co ntains register pointer and condition code. pc a t ix ep sp ps 16 bits : program counter : accumulator : temporary accumulator : index register : extra pointer : stack pointer : program status fffd h initial value not fixed not fixed not fixed not fixed not fixed i-flag = 0, il1, 0 = 11 other bits not fixed program status register configuration p s rp ccr 15 14 1 3 12 11 10 9 8 7654 3 21 0 rp open open open h i il1 il0 n z v c
mb89530a series ds07-12547-6e 27 the rp register shows the address of the register bank currently being used, so that the rp value and the actual address are related by the conversion ru le shown in the following illustration. the ccr register has bits that show the content of re sults of calculations and transferred data, and bits that control cpu operation during interrupts. in addition, the following general purpose registers are available. general purpose registers: 8 bits length, used to contain data. the general purpose registers are 8-bit registers locat ed in memory. there are eight such registers per bank, and the mb89530a series have up to 32 banks for use. the bank currently in use is indicated by the register bank pointer (rp). h-flag : set to ?1? if calculations result in carry or bo rrow operations from bit 3 to bit 4, otherwise set to ?0?. this flag is used for decimal correction instructions. i-flag : this flag is set to ?1? if interrupts are enabled, and ?0? if interrupts are prohibited. the default value at reset is ?0?. il1, 0 : indicates the level of th e currently permitted interrupts. only interrupt requests having a more powerful le vel than the value of thes e bits will be processed. il1 il0 interrupt level strength 00 1 strong weak 01 102 113 n-flag : set to ?1? if the high est bit is ?1? after a calculat ion, otherwise cleared to ?0?. z-flag : set to ?1? if a calculation re sult is ?0?, otherwise cleared to ?0?. v-flag : set to ?1? if a two?s complement overflow results during a calculation, otherwise cleared to ?0?. c-flag : set to ?1? if a calculation results in a carry or borrow operation from bit 7, otherwise cleared to ?0?. this is also the shift-out value in a shift instruction. general purpose register area real address conversion principle "0" "0" "0" "0" "0" "0" "0" "1" r4 r 3 r2 r1 r0 b 2 b 1 b 0 a7 a6 a5 a4 a 3 a2 a1 a0 a15 a14 a1 3 a12 a11 a10 a9 a 8 address generated rp upper o peration code lower
mb89530a series 28 ds07-12547-6e ? register bank configuration r0 r1 r2 r3 r4 r5 r6 r7 address at this location = 0100 h + 8 (rp) memory area 32 banks
mb89530a series ds07-12547-6e 29 i/o map (continued) address register name register description write/read initial value 00 h pdr0 port 0 data register r/w xxxxxxxx b 01 h ddr0 port 0 direction register w 0 0 0 0 0 0 0 0 b 02 h pdr1 port 1 data register r/w xxxxxxxx b 03 h ddr1 port 1 direction register w 0 0 0 0 0 0 0 0 b 04 h to 06 h (reserved area) 07 h sycc system clock control register r/w x -1 mm1 0 0 b 08 h stbc standby control register r/w 0 0 0 1 0 - - - b 09 h wdtc watchdog control register r/w 0 - - - xxxx b 0a h tbtc time base timer control register r/w 0 0 - - - 0 0 0 b 0b h wpcr watch prescaler control register r/w 0 0 - - 0 0 0 0 b 0c h pdr2 port 2 data register r/w xxxxxxxx b 0d h ddr2 port 2 direction register r/w 0 0 0 0 0 0 0 0 b 0e h pdr3 port 3 data register r/w xxxxxxxx b 0f h ddr3 port 3 direction register r/w 0 0 0 0 0 0 0 0 b 10 h pdr4 port 4 data register r/w xxxx 1 1 xx b 11 h ddr4 port 4 direction register r/w 0 0 0 0 - - 0 0 b 12 h pdr5 port 5 data register r/w 1 1 1 1 1 1 1 1 b 13 h pdr6 port 6 data register r xxxxxxxx b 14 h to 21 h (reserved area) 22 h smc11 serial mode control register 1 (uart) r/w 0 0 0 0 0 0 0 0 b 23 h src1 serial rate control register (uart) r/w - - 0 1 1 0 0 0 b 24 h ssd1 serial status and data register (uart) r/w 0 0 1 0 0 - 1x b 25 h sidr1/ sodr1 serial input/output data re gister (uart) r/w xxxxxxxx b 26 h smc12 serial mode control register 2 (uart) r/w - - 1 0 0 0 0 1 b 27 h cntr1 pwm control register 1 r/w 0 0 0 0 0 0 0 0 b 28 h cntr2 pwm control register 2 r/w 0 0 0 - 0 0 0 0 b 29 h cntr3 pwm control register 3 r/w - 0 0 0 - - - - b 2a h comr1 pwm compare register 1 w xxxxxxxx b 2b h comr2 pwm compare register 2 w xxxxxxxx b 2c h pcr1 pwc pulse width control register 1 r/w 0 0 0 - - 0 0 0 b 2d h pcr2 pwc pulse width control register 2 r/w 0 0 0 0 0 0 0 0 b 2e h rlbr pwc reload buffer register r/w xxxxxxxx b 2f h smc21 serial mode control register 1 (uart/sio) r/w 0 0 0 0 0 0 0 0 b 30 h smc22 serial mode control register 2 (uart/sio) r/w 0 0 0 0 0 0 0 0 b 31 h ssd2 serial status and data register ( uart / sio ) r/w 0 0 0 0 1 - - - b 32 h sidr2/ sodr2 serial data register (uart/sio) r/w xxxxxxxx b 33 h src2 baud rate generator reload register r/w xxxxxxxx b
mb89530a series 30 ds07-12547-6e (continued) address register name register description write/read initial value 34 h adc1 a/d control register 1 r/w 0 0 0 0 0 0 - 0 b 35 h adc2 a/d control register 2 r/w - 0 0 0 0 0 0 1 b 36 h addl a/d data register low r/w xxxxxxxx b 37 h addh a/d data register high r/w - - - - - - 0 0 b 38 h ppgc2 ppg2 control register (12-bit ppg) r/w 0 0 0 0 0 0 0 0 b 39 h prl22 ppg2 reload register 2 (12-bit ppg) r/w 0x0 0 0 0 0 0 b 3a h prl21 ppg2 reload register 1 (12-bit ppg) r/w xx0 0 0 0 0 0 b 3b h prl23 ppg2 reload register 3 (12-bit ppg) r/w xx0 0 0 0 0 0 b 3c h tmcr 16-bit timer control register r/w - - 0 0 0 0 0 0 b 3d h tchr 16-bit timer counter register high r/w 0 0 0 0 0 0 0 0 b 3e h tclr 16-bit timer counter register low r/w 0 0 0 0 0 0 0 0 b 3f h eic1 external interrupt 1 control register 1 r/w 0 0 0 0 0 0 0 0 b 40 h eic2 external interrupt 1 control register 2 r/w 0 0 0 0 0 0 0 0 b 41 h to 48 h (reserved area) 49 h ddcr ddc select register r/w - - - - - - - 0 b 4a h to 4b h (reserved area) 4c h ppgc1 ppg1 control register (12-bit ppg) r/w 0 0 0 0 0 0 0 0 b 4d h prl12 ppg1 reload register 2 (12-bit ppg) r/w 0x0 0 0 0 0 0 b 4e h prl11 ppg1 reload register 1 (12-bit ppg) r/w xx0 0 0 0 0 0 b 4f h prl13 ppg1 reload register 3 (12-bit ppg) r/w xx0 0 0 0 0 0 b 50 h iacr i 2 c address control register r/w - - - - - 0 0 0 b 51 h ibsr i 2 c bus status register r 0 0 0 0 0 0 0 0 b 52 h ibcr i 2 c bus control register r/w 0 0 0 0 0 0 0 0 b 53 h iccr i 2 c clock control register r/w 0 0 0 xxxxx b 54 h iadr i 2 c address register r/w - xxxxxxx b 55 h idar i 2 c data register r/w xxxxxxxx b 56 h eie2 external interrupt 2 control register r/w 0 0 0 0 0 0 0 0 b 57 h eif2 external interrupt 2 flag register r/w - - - - - - - 0 b 58 h rcr1 6-bit ppg control register 1 r/w 0 0 0 0 0 0 0 0 b 59 h rcr2 6-bit ppg control register 2 r/w 0x0 0 0 0 0 0 b 5a h ckr clock output control register r/w - - - - - - 0 0 b 5b h to 6f h (reserved area) 70 h smr serial mode register (sio) r/w 0 0 0 0 0 0 0 0 b 71 h sdr serial data register (sio) r/w xxxxxxxx b 72 h purr0 port 0 pull-up resistance register r/w 1 1 1 1 1 1 1 1 b 73 h purr1 port 1 pull-up resistance register r/w 1 1 1 1 1 1 1 1 b 74 h purr2 port 2 pull-up resistance register r/w 1 1 1 1 1 1 1 1 b 75 h purr3 port 3 pull-up resistance register r/w 1 1 1 1 1 1 1 1 b 76 h purr4 port 4 pull-up resistance register r/w 1 1 1 1 - -1 1 b 77 h wren wild register enable register r/w - - 0 0 0 0 0 0 b
mb89530a series ds07-12547-6e 31 (continued) description of write/read symbols : description of initial values : note : do not use reserved spaces. address register name register description write/read initial value 78 h wror wild register data test register r/w - - 0 0 0 0 0 0 b 79 h purr6 port 6 pull-up resistance register r/w - - - 1 1 1 1 1 b 7a h fmcs flash memory control status resister r/w 0 0 0x0 0 - 0 b 7b h ilr1 interrupt level setting register 1 w 1 1 1 1 1 1 1 1 b 7c h ilr2 interrupt level setting register 2 w 1 1 1 1 1 1 1 1 b 7d h ilr3 interrupt level setting register 3 w 1 1 1 1 1 1 1 1 b 7e h ilr4 interrupt level setting register 4 w 1 1 1 1 1 1 1 1 b 7f h itr interrupt test register access prohibited xxxxxx0 0 b c80 h wrarh1 upper address setting register 1 r/w xxxxxxxx b c81 h wrarl1 lower address sett ing register 1 r/w xxxxxxxx b c82 h wrdr1 data setting register 1 r/w xxxxxxxx b c83 h wrarh2 upper address setting register 2 r/w xxxxxxxx b c84 h wrarl2 lower address sett ing register 2 r/w xxxxxxxx b c85 h wrdr2 data setting register 2 r/w xxxxxxxx b c86 h wrarh3 upper address setting register 3 r/w xxxxxxxx b c87 h wrarl3 lower address sett ing register 3 r/w xxxxxxxx b c88 h wrdr3 data setting register 3 r/w xxxxxxxx b c89 h wrarh4 upper address setting register 4 r/w xxxxxxxx b c8a h wrarl4 lower address sett ing register 4 r/w xxxxxxxx b c8b h wrdr4 data setting register 4 r/w xxxxxxxx b c8c h wrarh5 upper address setting register 5 r/w xxxxxxxx b c8d h wrarl5 lower address sett ing register 5 r/w xxxxxxxx b c8e h wrdr5 data setting register 5 r/w xxxxxxxx b c8f h wrarh6 upper address setting register 6 r/w xxxxxxxx b c90 h wrarl6 lower address sett ing register 6 r/w xxxxxxxx b c91 h wrdr6 data setting register 6 r/w xxxxxxxx b r/w : read/write enabled r : read only w : write only 0 : this bit initialized to ?0?. 1 : this bit initialized to ?1?. x : the initial value of this bit is not determined. m : the initial value of this bit is a mask option. - : this bit is not used.
mb89530a series 32 ds07-12547-6e electrical characteristics 1. absolute maximum ratings *1 : the parameter is based on avss = vss = 0 v. *2 : avcc and vcc are to be used at the same potential. avr should not exceed avcc + 0.3 v. (continued) parameter symbol rating unit remarks min max supply voltage* 1 v cc , av cc v ss ? 0.3 v ss + 6.0 v mb89535a/537a/538a* 2 mb89537ac/538ac mb89f538/p538 mb89pv530 avr v ss ? 0.3 v ss + 6.0 v input voltage* 1 v i v ss ? 0.3 v cc + 0.3 v other than p42, p43 v ss ? 0.3 v ss + 6.0 v p42, p43 output voltage* 1 v o v ss ? 0.3 v cc + 0.3 v other than p42, p43 v ss ? 0.3 v ss + 6.0 v p42, p43 maximum clamp current i clamp ? 2.0 + 2.0 ma *3 total maximum clamp current | i clamp | ? 20 ma *3 ?l? level maximum output current i ol ? 15 ma ?l? level average output current i olav ? 4ma average value (operating current operating duty) ?l? level maximum total output current i ol ? 100 ma ?l? level average total output current i olav ? 40 ma average value (operating current operating duty) ?h? level maximum output current i oh ?? 15 ma ?h? level average output current i ohav ?? 4ma average value (operating current operating duty) ?h? level maximum total output current i oh ?? 50 ma ?h? level average total output current i ohav ?? 20 ma average value (operating current operating duty) current consumption p d ? 300 mw operating temperature t a ? 40 + 85 c storage temperature tstg ? 55 + 150 c
mb89530a series ds07-12547-6e 33 (continued) *3 : ? applicable to pins : p00 to p07, p10 to p17, p20 to p27, p30 to p37, p40, p41, p44 to p47, p60 to p64 ? use within recommended operating conditions. ? use at dc voltage (current) . ? the + b signal should always be applied with a limiting resistance placed between the + b signal and the microcontroller. ? the value of the limiting resistance should be set so that when the + b signal is applied the input current to the microcontroller pin does not exceed rated values , either instantaneously or for prolonged periods. ? note that when the microcontroller drive current is low, such as in the power saving modes, the + b input potential may pass through the protective di ode and increase the potential at the v cc pin, and this may affect other devices. ? note that if a + b signal is input when the microcon troller current is off (not fixe d at 0 v) , the power supply is provided from the pins, so that incomplete operation may result. ? note that if the + b input is applied during power-on, the powe r supply is provided from the pins and the resulting supply voltage may not be suffic ient to operate the power-on result. ? care must be taken not to leave the + b input pin open. ? note that analog system input/outpu t pins other than the a/d input pins (lcd drive pins, comparator input pins, etc.) cannot accept + b signal input. ? sample recommended circuits : warning: semiconductor devices can be permanently dama ged by application of stress (voltage, current, temperature, etc.) in excess of absolute ma ximum ratings. do not exceed these ratings. p-ch n-ch v cc r ? input/output equivalent circuits + b input (0 v to 16 v) limiting resistance protective diode
mb89530a series 34 ds07-12547-6e 2. recommended operating conditions (avss = vss = 0 v) * : varies according to frequen cy used, and instruction cycle. refer to ?operating voltage vs. operating frequency (m b89p538/mb89pv530) ?, ?oper ating voltage vs. operating frequency (mb89535a/537a/538a/537ac/ 538ac) ?, ?operating voltage vs . operating frequency (mb89f538) ? and ?5. a/d converter electrical characteristics?. parameter symbol value unit remarks min max supply voltage v cc , av cc 2.2* 5.5 v range warranted for normal operation mb89535a mb89537a/538a mb89537ac/ 538ac 1.5 5.5 v ram status in stop mode 2.7* 5.5 v range warranted for normal operation mb89p538 mb89pv530 1.5 5.5 v ram status in stop mode 3.5 5.5 v range warranted for normal operation mb89f538 3.0 5.5 v ram status in stop mode avr 3.5 av cc v operating temperature t a ? 40 + 85 c
mb89530a series ds07-12547-6e 35 ? operating voltage vs. operatin g frequency (mb89p538/mb89pv530) ? operating voltage vs. operating fr equency (mb89535a/537a/538a/537ac/538ac) 5.5 5.0 4.0 3.5 3.0 2.0 2.2 2.7 1.0 0 1.0 4.0 2.0 2.0 3.0 4.0 5.0 0.8 6.0 7.0 8.0 9.0 10.0 0.4 11.0 12.0 12.5 0.32 range of warranted analog precision : v cc = av cc = 3.5 v to 5.5 v operating voltage v cc (v) operating frequency (mhz) (at instruction cycle = 4 / f ch ) minimum instruction execution time (instruction cycles) ( s) indicates warranted operation at t a = ? 10 c to + 55 c 5.5 5.0 4.0 3.5 3.0 2.0 2.2 2.7 1.0 0 1.0 4.0 2.0 2.0 3.0 4.0 5.0 0.8 6.0 7.0 8.0 9.0 10.0 0.4 11.0 12.0 12.5 0.32 range of warranted analog precision : v cc = av cc = 3.5 v to 5.5 v operating voltage v cc (v) operating frequency (mhz) (at instruction cycle = 4 / f ch ) minimum instruction execution time (instruction cycles) ( s)
mb89530a series 36 ds07-12547-6e ? operating voltage vs. operating frequency (mb89f538) warning: the recommended operating co nditions are required in order to ensure the normal operation of the semiconductor device. all of the device's el ectrical characteristics are warranted when the device is operated within these ranges. always use semiconductor devices within their recommended operating condition ranges. operation outside these ranges may adversely affect reliability and could result in device failure. no warranty is made with respect to uses, operat ing conditions, or combinations not represented on the data sheet. users considering application outs ide the listed conditions are advised to contact their representatives beforehand. 5.5 5.0 4.0 3.5 3.0 2.0 1.0 0 1.0 4.0 2.0 2.0 3.0 4.0 5.0 0.8 6.0 7.0 8.0 9.0 10.0 0.4 11.0 12.0 12.5 0.32 range of warranted analog precision : v cc = av cc = 3.5 v to 5.5 v operating voltage v cc (v) operating frequency (mhz) minimum instruction execution ti me (instruction cycles) ( s)
mb89530a series ds07-12547-6e 37 3. dc characteristics (1) supply voltage at 5.0 (v) (av cc = v cc = 5.0 v, avss = vss = 0 v, t a = ? 40 c to + 85 c) (continued) parameter symbol pin name condi- tion value unit remarks min typ max ?h? level input voltage v ih p00 to p07, p10 to p17, p20 to p27, p30 to p37, p40 to p47, p60 to p64, si1, si2 ? 0.7 v cc ? v cc + 0.3 v v ihs rst , mod0, mod1, int20 to int27, uck1, ui1, int10 to int13, sck1, ec, pwck, pwc, sck2, uck2, ui2, adst ? 0.8 v cc ? v cc + 0.3 v v ihsmb scl, sda ? v ss + 1.4 ? v ss + 5.5 v with smb input buffer selected* 1 v ihi2c ? 0.7 v cc ? v ss + 5.5 v with i 2 c input buffer selected* 1 ?l? level input voltage v il p00 to p07, p10 to p17, p20 to p27, p30 to p37, p40 to p47, p60 to p64, si1, si2 ? v ss ? 0.3 ? 0.3 v cc v v ils rst , mod0, mod1, int20 to int27, uck1, ui1, int10 to int13, sck1, ec, pwck, pwc, sck2, uck2, ui2, adst ? v ss ? 0.3 ? 0.2 v cc v v ilsmb scl, sda ? v ss ? 0.3 ? v ss + 0.6 v with smb input buffer selected* 1 v ili2c ? v ss ? 0.3 ? 0.3 v cc v with i 2 c input buffer selected* 1 open drain output applied voltage v d1 p50 to p57 ? v ss ? 0.3 ? v cc + 0.3 v v d2 p42, p43 v ss + 5.5 v ?h? level output voltage v oh p00 to p07, p10 to p17, p20 to p24, p30 to p37, p40, p41, p44 to p47 i oh = ? 2.0 ma 4.0 ?? v p25 to p27 i oh = ? 3.0 ma ?l? level output voltage v ol p00 to p07, p10 to p17, p20 to p27, p30 to p37, p40 to p47, p50 to p57, rst i ol = 4.0 ma ?? 0.4 v
mb89530a series 38 ds07-12547-6e (av cc = v cc = 5.0 v, avss = vss = 0 v, t a = ? 40 c to + 85 c) (continued) parameter symbol pin name condition value unit remarks min typ max input leak current (hi-z output leak current) i li p00 to p07, p10 to p17, p20 to p27, p30 to p37, p40 to p47, p50 to p57, p60 to p64 0.0 v < v i < v cc ? 5 ?+ 5 a with no pull-up re- sistance specified open drain output leak current i liod p42, p43 0.0 v < v i < v ss + 5.5 v ?? 5 a pull-up resistance r up p00 to p07, p10 to p17, p20 to p27, p30 to p37, p40, p41, p44 to p46, p47* 2 , p60 to p64, rst ? 25 40 100 k ? with pull-up resistance speci- fied. the rst signal is excluded. pull-down resistance r down mod0, mod1 ? 25 40 100 k ? only for mask rom product. supply current i cc1 v cc f ch = 10.0 mhz v cc = 5.0 v t inst = 0.4 s ? 15 20 ma mb89p538/ pv530 ? 6 10 ma mb89f538 ? 813ma mb89535a/7a/8a mb89537ac/ 538ac i cc2 f ch = 10.0 mhz v cc = 5.0 v t inst = 6.4 s ? 58.5ma mb89p538/ pv530 ? 1.5 3 ma mb89f538 ? 1.5 3 ma mb89535a/7a/8a mb89537ac/ 538ac i ccs1 f ch = 10.0 mhz v cc = 5.0 v t inst = 0.4 s ? 57ma sleep mode mb89p538/ pv530 ? 35ma sleep mode mb89f538 ? 2.5 5 ma sleep mode mb89535a/7a/8a mb89537ac/ 538ac i ccs2 f ch = 10.0 mhz v cc = 5.0 v t inst = 6.4 s ? 1.5 3 ma sleep mode mb89p538/ pv530 ? 12ma sleep mode mb89f538 ? 12ma sleep mode mb89535a/7a/8a mb89537ac/ 538ac
mb89530a series ds07-12547-6e 39 (continued) (av cc = v cc = 5.0 v, avss = vss = 0 v, t a = ? 40 c to + 85 c) *1 : the mb89pv530/p538/537ac/538ac have a built-in i 2 c function, and a choice of input buffers by software setting. mb89535a/537a/538a have no built-in i 2 c functions, and therefore th is standard does not apply. *2 : for p47 of mb89f538, pull-up resistor is not mounted as this pin is used as mod2 pin. parameter symbol pin name condition value unit remarks min typ max supply current i ccl v cc f cl = 32.768 khz v cc = 5.0 v t a = + 25 c ? 37ma sub mode mb89p538/ pv530 ? 400 800 a sub mode mb89f538 ? 50 85 a sub mode mb89535a/7a/8a mb89537ac/ 538ac i ccls f cl = 32.768 khz v cc = 5.0 v t a = + 25 c ? 30 50 a sub, sleep mode mb89p538/ pv530 ? 15 30 a sub, sleep mode mb89f538 ? 15 30 a sub, sleep mode mb89535a/7a/8a mb89537ac/ 538ac i cct f cl = 32.768 khz v cc = 5.0 v t a = + 25 c ? 515 a watch mode, main stop i cch t a = + 25 c ? 310 a sub, stop modes i a av cc f ch = 10.0 mhz ? 46ma a/d conversion running i ah t a = + 25 c ? 15 a a/d stopped input capacitance c in except v cc , v ss , av cc , av ss f = 1 mhz ? 515pf
mb89530a series 40 ds07-12547-6e (2) supply voltage at 3.0 (v) (except mb89f538) (av cc = v cc = 3.0 v, avss = vss = 0 v, t a = ? 40 c to + 85 c) (continued) parameter symbol pin name condition value unit remarks min typ max ?h? level input voltage v ih p00 to p07, p10 to p17, p20 to p27, p30 to p37, p40 to p47, p60 to p64, si1, si2 ? 0.7 v cc ? v cc + 0.3 v v ihs rst , mod0, mod1, int20 to int27, uck1, ui1, int10 to int13, sck1, ec, pwck, pwc, sck2, uck2, ui2, adst ? 0.8 v cc ? v cc + 0.3 v v ihsmb scl, sda ? v ss + 1.4 ? v ss + 5.5 v with smb input buffer selected* v ihi2c ? 0.7 v cc ? v ss + 5.5 v with i 2 c input buffer selected* ?l? level input voltage v il p00 to p07, p10 to p17, p20 to p27, p30 to p37, p40 to p47, p60 to p64, si1, si2 ? v ss ? 0.3 ? 0.3 v cc v v ils rst , mod0, mod1, int20 to int27, uck1, ui1, int10 to int13, sck1, ec, pwck, pwc, sck2, uck2, ui2, adst ? v ss ? 0.3 ? 0.2 v cc v v ilsmb scl, sda ? v ss ? 0.3 ? v ss + 0.6 v with smb input buffer selected* v ili2c ? v ss ? 0.3 ? 0.3 v cc v with i 2 c input buffer selected* open drain output applied voltage v d1 p50 to p57 ? v ss ? 0.3 ? v cc + 0.3 v v d2 p42, p43 v ss + 5.5 v ?h? level output voltage v oh p00 to p07, p10 to p17, p20 to p24, p30 to p37, p40, p41, p44 to p47 i oh = ? 2.0 ma 2.4 ?? v p25 to p27 i oh = ? 3.0 ma ?l? level output voltage v ol p00 to p07, p10 to p17, p20 to p27, p30 to p37, p40 to p47, p50 to p57, rst i ol = 4.0 ma ?? 0.4 v
mb89530a series ds07-12547-6e 41 (continued) (av cc = v cc = 3.0 v, avss = vss = 0 v, t a = ? 40 c to + 85 c) * : the mb89pv530/p538/537ac/538ac have a built-in i 2 c function, and a choice of input buffers by software setting. mb89535a/537a/538a have no built-in i 2 c functions, and therefore this standard does not apply. parameter symbol pin name condition value unit remarks min typ max input leak current (hi-z output leak current) i li p00 to p07, p10 to p17, p20 to p27, p30 to p37, p40 to p47, p50 to p57, p60 to p64 0.0 v < v i < v cc ? 5 ?+ 5 a with no pull-up resistance specified open drain output leak current i liod p42, p43 0.0 v < v i < v ss + 5.5 v ?? 5 a pull-up resistance r up p00 to p07, p10 to p17, p20 to p27, p30 to p37, p40, p41, p44 to p47, p60 to p64, rst ? 25 70 100 k ? with pull-up resistance specified. the rst signal is excluded. pull-down resistance r down mod0, mod1 ? 25 70 100 k ? supply current i cc1 v cc f ch = 10.0 mhz t inst = 0.4 s ? 610ma i cc2 f ch = 10.0 mhz t inst = 6.4 s ? 1.5 3 ma i ccs1 f ch = 10.0 mhz t inst = 0.4 s ? 2 4 ma sleep mode i ccs2 f ch = 10.0 mhz t inst = 6.4 s ? 1 2 ma sleep mode i ccl f cl = 32.768 khz v cc = 3.0 v t a = + 25 c ? 13ma sub modes mb89p538/pv530 ? 20 50 a sub modes mb89535a/7a/8a mb89537ac/538ac i ccls f cl = 32.768 khz v cc = 3.0 v t a = + 25 c ? 15 30 a sub, sleep modes i cct f cl = 32.768 khz v cc = 3.0 v t a = + 25 c ? 515 a watch mode, main stop i cch t a = + 25 c ? 15 a sub, stop modes i a av cc f ch = 10.0 mhz ? 13ma a/d conversion running i ah t a = + 25 c ? 15 a a/d stopped input capacitance c in except v cc , v ss , av cc , av ss f = 1 mhz ? 515pf
mb89530a series 42 ds07-12547-6e 4. ac characteristics (1) reset timing (v cc = 5.0 v, avss = vss = 0 v, t a = ? 40 c to + 85 c) notes: ? t hcyl is the main clock oscillator period. ? if the reset pulse applied to the external reset pin (rst ) does not meet the specifications, it may cause malfunctions. use caution so that the reset puls e less than the specifications will not be fed to the external reset pin (rst ). (2) power-on reset (avss = vss = 0 v, t a = ? 40 c to + 85 c) note : be sure that the power supply will come on within the selected os cillator stabilization period. also, when varying the supply voltage during operation, it is reco mmended that the supply voltage be increased gradually. parameter symbol condition value unit min max rst ?l? pulse width t zlzh ? 48 t hcyl ? ns parameter symbol condition value unit remarks min max power on time t r ? 0.5 50 ms power shutoff time t off ? 1 ? ms waiting time until power-on rst 0.2 v cc 0.2 v cc t zlzh v cc t r 2.2 v 0.2 v 0.2 v 0.2 v t off
mb89530a series ds07-12547-6e 43 (3) clock timing standards (avss = vss = 0 v, t a = ? 40 c to + 85 c) parameter symbol pin name condition value unit remarks min typ max clock frequency f ch x0, x1 ? 1 ? 12.5 mhz main clock f cl x0a, x1a ? 32.768 ? khz sub clock clock cycle time t hcyl x0, x1 80 ? 1000 ns main clock t lcyl x0a, x1a ? 30.5 ? ssub clock input clock pulse width p wh p wl x0 20 ?? ns external clock p whl p wll x0a ? 15.2 ? s external clock input clock rise, fall time t cr t cf x0 ?? 10 ns external clock ? x0 , x1 timing and app lication conditions ? clock application conditions t hcyl p wh t cr t cf p wl 0.2 v cc 0.2 v cc 0.2 v cc 0.8 v cc 0.8 v cc x0 x0 x1 c 1 c 2 f ch f ch x0 x1 using a crystal oscillator or ceramic oscillator using an external clock signal open
mb89530a series 44 ds07-12547-6e (4) instruction cycle (avss = vss = 0 v, t a = ? 40 c to + 85 c) parameter symbol rated value unit remarks instruction cycle (minimum instruction execution time) t inst 4/f ch , 8/f ch , 16/f ch , 64/f ch s operating at f ch = 12.5 mhz (4/f ch ) t inst = 0.32 s 2/f cl s operating at f cl = 32.768 khz t inst = 61.036 s ? x0a, x1a timing and application conditions ? clock application conditions t lcyl p whl t cr t cf p wll 0.2 v cc 0.2 v cc 0.2 v cc 0.8 v cc 0.8 v cc x0a x0a x1a rd x0a x1a c 1 c 2 f cl f cl using a crystal oscillator or ceramic oscillator using an external clock signal open
mb89530a series ds07-12547-6e 45 (5) serial i/o timing (v cc = 5.0 v, avss = vss = 0 v, t a = ? 40 c to + 85 c) note : for t inst refer to ? (4) instruction cycle?. parameter symbol pin name condition value unit min max serial clock cycle time t scyc sck, uck internal clock operation 2 t inst ? s sck so t slov sck, so, uck, uo ? 200 + 200 ns valid si sck t ivsh si, sck, ui, uck 200 ? ns sck valid si hold time t shix sck, si, uck, ui 200 ? ns serial clock ?h? pulse width t shsl sck, uck external clock operation 1 t inst ? s serial clock ?l? pulse width t slsh 1 t inst ? s sck so time t slov sck, so, uck, uo 0 200 ns valid si sck t ivsh si, sck, ui, uck 200 ? ns sck valid si hold time t shix sck, si, uck, ui 200 ? ns internal shift clock mode external shift clock mode sck uck so uo si ui t scyc t ivsh t slov t shix 0.8 v 0.8 v 2.4 v 0.8 v cc 0.2 v cc 0.8 v cc 0.2 v cc 0.8 v 2.4 v sck uck so uo si ui t slsh t shsl t ivsh t slov t shix 0.2 v cc 0.8 v 2.4 v 0.8 v cc 0.2 v cc 0.8 v cc 0.2 v cc 0.2 v cc 0.8 v cc 0.8 v cc
mb89530a series 46 ds07-12547-6e (6) peripheral input timing (v cc = 5.0 v, avss = vss = 0 v, t a = ? 40 c to + 85 c) note : for t inst refer to ? (4) instruction cycle?. parameter symbol pin name condition value unit min max peripheral input ?h? level pulse width 1 t ilih1 int10 to int13, int20 to int27, ec, pwc, pwck ? 2 t inst ? s peripheral input ?l? level pulse width 1 t ihil1 ? 2 t inst ? s peripheral input ?h? level pulse width 2 t ilih2 adst ? 2 8 t inst ? s peripheral input ?l? level pulse width 2 t ihil2 ? 2 8 t inst ? s ec, int, pwc, pwck t ihil1 t ilih1 0.2 v cc 0.2 v cc 0. 8 v cc 0. 8 v cc ad s t t ihil2 t ilih2 0.2 v cc 0.2 v cc 0. 8 v cc 0. 8 v cc
mb89530a series ds07-12547-6e 47 (7) i 2 c timing (v cc = 5.0 v, avss = vss = 0 v, t a = ? 40 c to + 85 c) notes : ? for t inst refer to ? (4) instruction cycle?. ? the value ?m? in the above table is the value from th e shift clock frequency setting bits (cs4, cs3) in the i 2 c clock control register ?iccr?. for details, refer to the register description in the hardware manual. ? the value ?n? in the above table is the value from th e shift clock frequency setting bits (cs2, cs0) in the i 2 c clock control register ?iccr?. for details, refer to the register description in the hardware manual. ? t dosu appears when the interrupt period is longer than the scl ?l? width. ? the rated values for sda and scl assume a start up time of 0 ns. parameter symbol pin name condition value unit remarks min max start condition output t sta scl sda ? 1 / 4 t inst m n ? 20 1 / 4 t inst m n + 20 ns master only stop condition output t sto scl sda ? 1 / 4 t inst (m n + 8) ? 20 1 / 4 t inst (m n + 8) + 20 ns master only start condition detection t sta scl sda ? 1 / 4 t inst 6 + 40 ? ns stop condition detection t sto scl sda ? 1 / 4 t inst 6 + 40 ? ns restart condition output t stasu scl sda ? 1 / 4 t inst (m n + 8) ? 20 1 / 4 t inst (m n + 8) + 20 ns master only restart condition detection t stasu scl sda ? 1 / 4 t inst 4 + 40 ? ns scl output ?l? width t low scl ? 1 / 4 t inst m n ? 20 1 / 4 t inst m n + 20 ns master only scl output ?h? width t high scl ? 1 / 4 t inst (m n + 8) ? 20 1 / 4 t inst (m n + 8) + 20 ns master only sda output delay time t do sda ? 1 / 4 t inst 4 ? 20 1 / 4 t inst 4 + 20 ns setup after sda output interrupt interval t dosu sda ? 1 / 4 t inst 4 ? 20 ? ns scl input ?l? width t low scl ? 1 / 4 t inst 6 + 40 ? ns scl input ?h? width t high scl ? 1 / 4 t inst 2 + 40 ? ns sda input setup t su sda ? 40 ? ns sda input hold t ho sda ? 0 ? ns
mb89530a series 48 ds07-12547-6e ? i 2 c interface [data sending (master/slave) ] ? i 2 c interface [data receiving (master/slave) ] 9 ack t do t su t su t dosu t do t ho t low t sta t stasu sda scl 1 s da s cl 67 8 9 t s u t high t low t ho t do t do t do s u t s to ack
mb89530a series ds07-12547-6e 49 5. a/d converter electrical characteristics (1) mb89535a/537a/537a c/538a/538ac/p538/pv530 (v cc = 3.5 v to 5.5 v, av ss = v ss = 0 v, t a = ? 40 c to + 85 c) * : includes sampling time. note : for t inst refer to ?4. ac characteri stics (4) instruction cycle?. (2) mb89f538 (v cc = 3.5 v to 5.5 v, av ss = v ss = 0 v, t a = ? 40 c to + 85 c) * : includes sampling time. note : for t inst refer to ?4. ac characteri stics (4) instruction cycle?. parameter symbol pin name condition value unit remarks min typ max resolution capability ? ? ??? 10 bit av cc = v cc total error avr = av cc ?? 3.0 lsb linear error ?? 2.5 lsb differential linear error ?? 1.9 lsb zero transition voltage v ot av ss ? 1.5 lsb av ss + 0.5 lsb av ss + 2.5 lsb mv full scale transition voltage v fst avr ? 3.5 lsb avr ? 1.5 lsb avr + 1.5 lsb mv inter-channel variation ? ?? 4.0 lsb conversion time ? ? 60 t inst ? s* sampling time ? 16 t inst ? s analog input current i ain an0 to an7 ?? 10 a analog input voltage v ain 0 ? avr v reference voltage ? avr av ss + 3.5 ? av cc v reference voltage supply current i r a/d running ? 400 ? a i rh a/d off ?? 5 a parameter symbol pin name condition value unit remarks min typ max resolution capability ? ? ??? 10 bit av cc = v cc total error avr = av cc ?? 5.0 lsb linear error ?? 2.5 lsb differential linear error ?? 1.9 lsb zero transition voltage v ot av ss ? 1.5 lsb av ss + 0.5 lsb av ss + 4.5 lsb mv full scale transition voltage v fst avr ? 6.5 lsb avr ? 1.5 lsb avr + 1.5 lsb mv inter-channel variation ? ?? 4.0 lsb conversion time ? ? 60 t inst ? s* sampling time ? 16 t inst ? s analog input current i ain an0 to an7 ?? 10 a analog input voltage v ain 0 ? avr v reference voltage ? avr av ss + 3.5 ? av cc v reference voltage supply current i r a/d running ? 400 ? a i rh a/d off ?? 5 a
mb89530a series 50 ds07-12547-6e (3) a/d converter terms and definitions ? resolution the level of analog variation that can be distinguished by the a/d converter. ? linear error (unit : lsb) the deviation between the value along a strai ght line connecting the zero transition point (?00 0000 0000? ?00 0000 0001?) of a device and the full-scale transition point (?11 1111 1110? ?11 1111 1111?) , compared with the actual conversion values obtained. ? differential linear error (unit : lsb) the deviation from the theoretical input voltage requ ired to produce a change of 1 lsb in output code. ? total error (unit : lsb) the difference between theoretical conver sion value and actual conversion value. (continued) v fst 1.5 lsb 1 lsb 0.5 lsb v ot avr av ss 3ff h 3fe h 3fd h 004 h 003 h 002 h 001 h v nt (1 lsb i n + 0.5 lsb) avr av ss 3ff h 3fe h 3fd h 004 h 003 h 002 h 001 h theoretical input/output characteristics analog input digital output 1 lsb = v fst ? v ot 1022 (v) total error analog input digital output total error in digital output n = v nt ? {1 lsb n + 0.5 lsb} 1 lsb actual conversion characteristics actual conversion characteristics theoretical characteristics
mb89530a series ds07-12547-6e 51 (continued) 004 h 003 h 002 h 001 h av ss 3ff h 3fe h 3fd h 3fc h avr 3ff h 3fe h 3fd h 004 h 003 h 002 h 001 h av ss avr v nt (1 lsb n + v ot ) v (n + 1) t v nt n + 1 h n h n ? 1 h n ? 2 h av ss avr zero transition error analog input full-scale transition error digital output digital output linear error analog input differential linear error analog input digital output digital output ? 1 differential linear error in digital output n v ( n + 1 ) t ? v nt 1 lsb actual conversion characteristics actual conversion characteristics v ot (actual measurement value) actual conversion characteristics v fst ( actual measurement value ) actual conversion characteristics actual conversion characteristics v ot ( actual measurement value ) v fst (actual measure- ment value) theoretical characteristics actual conversion characteristics actual conversion characteristics theoretical characteristics actual conversion characteristics analog input linear error in digital output n v nt ? {1 lsb n + v ot } 1 lsb theoretical characteristics = = analog input
mb89530a series 52 ds07-12547-6e (4) precautionary information ? input impedance of analog input pins the a/d converter of mb89530a has a sample & hold ci rcuit as shown below, which uses a sample-and-hold capacitor to obtain the voltage at the analog input pin for 8 instruction cycles following the start of a/d conversion. for this reason if the external circuits providing t he analog input signal have high output impedance, the analog input voltage may not stabilize within the analog input sa mpling time. it is therefore recommended that the output impedance of external circuits be reduced to 10 k ? or less. ? about error the smaller the absolute value |avr - avss| is, the greater the relative error becomes. ? mb89535a/537a/537ac/538a /538ac analog input equivalent circuit c = 45 pf r = 2.2 k ? comp a r a tor if analog input impedance is 10 k ? or more, the use of a capacitor of approximately 0.1 f is recommended. analog input pin sample-and-hold circuit closes 8 instruction cycles after the start of a/d conversion analog channel selector ? mb89p538 and mb89pv530 analog input equivalent circuit c = 64 pf r = 3 k ? comp a r a tor if analog input impedance is 10 k ? or more, the use of a capacitor of approximately 0.1 f is recommended. analog input pin sample-and-hold circuit closes 8 instruction cycles after the start of a/d conversion analog channel selector ? mb89f538 analog input equivalent circuit c = 3 0 pf r = 3 .2 k ? comp a r a tor analog channel selector analog input pin if analog input impedance is 10 k ? or more, the use of a capacitor of approximately 0.1 f is recommended. closes 8 instruction cycles after the start of a/d conversion sample-and-hold circuit
mb89530a series ds07-12547-6e 53 6. flash memory flash memory programming/erase characteristics * : excludes internal programming time before erase. parameter conditions value unit remarks min typ max sector erase time per 1 sector, constant value independent with sector capacitance t a = + 25 c, v cc = 5.0 v ? 115s* programming time per 1 byte ? 8 3600 s chip erase time ? 5 ? s* program/erase cycle ? 10000 ?? cycle
mb89530a series 54 ds07-12547-6e example characteristics (mb89538a) (1) power supply current (external clock) (2) ?h? level input voltage/ ?l? level input voltage (cmos input) (3) ?h? level input voltage / ?l? le vel input voltage (hysteresis input) i cc1 vs. v cc 0 2 4 6 8 10 12 14 234567 v cc (v) i cc1 (ma) (t a = + 25 ?c) 12.5 mhz 1 mhz 2 mhz 5 mhz 8 mhz 10 mhz i ccs1 vs. v cc 0 1 2 3 4 5 234567 v cc (v) i ccs1 (ma) (t a = + 25 ?c) 12.5 mhz 1 mhz 2 mhz 5 mhz 8 mhz 10 mhz v in vs. v cc 0 1 2 3 4 234567 v cc (v) v in (v) (t a = + 25 ?c) v in vs. v cc 0 1 2 3 4 234567 v cc (v) v in (v) (t a = + 25 ?c) v ih v il
mb89530a series ds07-12547-6e 55 (4) pull-up resistor value (5) ?h? level output voltage (6) ?l? level output voltage r pull vs. v cc 10 100 1000 0345 26 v cc (v) pull-up (k ? ) (t a = + 25 ?c) 1 v cc - v oh1 vs. i oh 0.0 1.0 1.2 1.4 1.6 0 468 210 i oh (ma) v cc - v oh1 (v) (t a = + 25 ?c, v cc = 5 v) 0.4 0.2 0.6 0.8 v cc - v oh2 vs. i oh 0.0 0.5 0.6 0.7 0.8 0 468 210 i oh (ma) v cc - v oh2 (v) (t a = + 25 ?c, v cc = 5 v) 0.2 0.1 0.3 0.4 0.9 v cc - v ol vs. i ol 0.0 0.5 0.6 0.7 0.8 0 468 210 i ol (ma) v cc - v ol (v) (t a = + 25 ?c, v cc = 5 v) 0.2 0.1 0.3 0.4 0.9
mb89530a series 56 ds07-12547-6e (7) ad converter characteristic example -2.5 0.0 1.5 2.0 2.5 0 640 768 896 512 1024 (v cc = avr = 5 v, f ch = 10 mhz) -1.5 -2.0 -1.0 -0.5 3.0 128 256 384 -3.0 1.0 0.5 -2.5 0.0 1.5 2.0 2.5 0 640 768 896 512 1024 -1.5 -2.0 -1.0 -0.5 128 256 384 1.0 0.5 -4.0 0.0 2.0 3.0 4.0 0 640 768 896 512 1024 (v cc = avr = 5 v, f ch = 10 mhz) -2.0 -3.0 -1.0 128 256 384 1.0 linearity error error (lsb) conversion characteristic differential linearity error error (lsb) conversion characteristic total error error (lsb) conversion characteristic
mb89530a series ds07-12547-6e 57 mask options * : f ch : main clock frequency no part number mb89535a mb89537a mb89537ac mb89538a mb89538ac mb89f538-101 mb89f538-201 mb89p538-101 mb89p538-201 mb89pv530-101 mb89pv530-201 method of specification specify at time of mask order setting not possible setting not possible setting not possible 1 main clock select oscillator stabilization wait period (f ch * = 10 mhz) approx.2 14 /f ch * (approx.1.6 ms) approx.2 17 /f ch * (approx.13.1 ms) approx.2 18 /f ch * (approx.26.2 ms) selection available 2 18 /f ch * (approx. 26.2 ms) 2 18 /f ch * (approx. 26.2 ms) 2 18 /f ch * (approx. 26.2 ms) 2 clock mode selection ? 2-system clock mode ? 1-system clock mode selection available ? 101 : 1-system clock mode ? 201 : 2-system clock mode
mb89530a series 58 ds07-12547-6e ordering information * : only for es part number package remarks mb89535ap mb89537ap mb89537acp mb89538ap mb89538acp mb89p538p-101 mb89p538p-201 mb89f538p-101 mb89f538p-201 dip-64p-m01 mb89535ap, mb89537ap and mb89538ap do not have i 2 c functions. mb89535apf mb89537apf mb89537acpf mb89538apf mb89538acpf mb89p538pf-101 mb89p538pf-201 mb89f538pf-101 mb89f538pf-201 fpt-64p-m06 mb89535apf, mb89537apf and mb89538apf do not have i 2 c functions. mb89535apfm mb89537apfm mb89537acpfm mb89538apfm mb89538acpfm mb89p538pfm-101 mb89p538pfm-201 mb89f538pfm-101 mb89f538pfm-201 fpt-64p-m09 mb89535apfm, mb89537apfm and mb89538apfm do not have i 2 c functions. mb89535apfv mb89537apfv mb89537acpfv mb89538apfv mb89538acpfv fpt-64p-m03 mb89535apfv, mb89537apfv and mb89538apfv do not have i 2 c functions. mb89535apv4 mb89537apv4 mb89537acpv4 mb89538apv4 mb89538acpv4 lcc-64p-m19 mb89535apv4, mb89537apv4, and mb89538apv4 do not have i 2 c functions. mb89p538-101pv* mb89p538-201pv* lcc-64p-m16* mb89pv530c-101 MB89PV530C-201 mdp-64c-p02 mb89pv530cf-101 mb89pv530cf-201 mqp-64c-p01
mb89530a series ds07-12547-6e 59 package dimensions please confirm the latest package dimension by following url. http://edevice.fujitsu.com/package/en-search/ (continued) 64-pin pl as tic s h-dip le a d pitch 1.778mm(70mil) p a ck a ge width p a ck a ge length 17 58 mm s e a ling method pl as tic mold mo u nting height 5.65 mm max 64-pin pl as tic s h-dip (dip-64p-m01) (dip-64p-m01) c 2001-2008 fujit s u microelectronic s limited d64001 s -c-4-6 58.00 +0.22 ?0.55 +.009 ?.022 2.283 17.000.25 (.669.010) 3.30 +0.20 ?0.30 .130 ?.012 +.008 +.028 ?.008 .195 ?0.20 +0.70 4.95 +.016 ?.008 .0543 ?0.20 +0.40 1.378 1.778(.0700) 0.470.10 (.019.004) 1.00 +0.50 ?0 .039 ?.0 +.020 +.020 ?.007 .028 ?0.19 +0.50 0.70 19.05(.750) (.011.004) 0.270.10 0~15 index-2 index-1 m 0.25(.010) dimen s ion s in mm (inche s ). note: the v a l u e s in p a renthe s e s a re reference v a l u e s . note: pin s width a nd pin s thickne ss incl u de pl a ting thickne ss .
mb89530a series 60 ds07-12547-6e please confirm the latest package dimension by following url. http://edevice.fujitsu.com/package/en-search/ (continued) 64-pin pl as tic lqfp le a d pitch 0.50 mm p a ck a ge width p a ck a ge length 10.0 10.0 mm le a d s h a pe g u llwing s e a ling method pl as tic mold mo u nting height 1.70 mm max weight 0. 3 2g code (reference) p-lfqfp64-10 10-0.50 64-pin pl as tic lqfp (fpt-64p-m0 3 ) (fpt-64p-m0 3 ) lead no. det a il s of "a" p a rt 0.25(.010) ( s t a nd off) (.004.004) 0.100.10 (.024.006) 0.600.15 (.020.00 8 ) 0.500.20 1.50 +0.20 ?0.10 +.00 8 ?.004 .059 0 ~ 8 "a" 0.0 8 (.00 3 ) (.006.002) 0.1450.055 0.0 8 (.00 3 ) m (.00 8 .002) 0.200.05 0.50(.020) 12.000.20(.472.00 8 ) s q 10.000.10(. 3 94.004) s q index 49 64 33 4 8 17 3 2 16 1 200 3 -200 8 fujit s u microelectronic s limited f64009 s -c-5-9 c (mo u nting height) * dimen s ion s in mm (inche s ). note: the v a l u e s in p a renthe s e s a re reference v a l u e s note 1) * : the s e dimen s ion s do not incl u de re s in protr us ion. note 2) pin s width a nd pin s thickne ss incl u de pl a ting thickne ss . note 3 )pin s width do not incl u de tie ba r c u tting rem a inder.
mb89530a series ds07-12547-6e 61 please confirm the latest package dimension by following url. http://edevice.fujitsu.com/package/en-search/ (continued) 64-pin pl as tic qfp le a d pitch 1.00 mm p a ck a ge width p a ck a ge length 14 20 mm le a d s h a pe g u llwing s e a ling method pl as tic mold mo u nting height 3 . 3 5 mm max code (reference) p-qfp64-14 20-1.00 64-pin pl as tic qfp (fpt-64p-m06) (fpt-64p-m06) c 200 3 -200 8 fujit s u microelectronic s limited f6401 3s -c-5-6 0.20(.00 8 ) m 1 8 .700.40 (.7 3 6.016) 14.000.20 (.551.00 8 ) 1.00(.0 3 9) index 0.10(.004) 119 20 3 2 52 64 33 51 20.000.20(.7 8 7.00 8 ) 24.700.40(.972.016) 0.420.0 8 (.017.00 3 ) 0.170.06 (.007.002) 0~ 8 1.200.20 (.047.00 8 ) 3 .00 +0. 3 5 ?0.20 (mo u nting height) .11 8 +.014 ?.00 8 0.25 +0.15 ?0.20 .010 +.006 ?.00 8 ( s t a nd off) det a il s of "a" p a rt "a" 0.10(.004) * * dimen s ion s in mm (inche s ). note: the v a l u e s in p a renthe s e s a re reference v a l u e s . note 1) * : the s e dimen s ion s do not incl u de re s in protr us ion. note 2) pin s width a nd pin s thickne ss incl u de pl a ting thickne ss . note 3 )pin s width do not incl u de tie ba r c u tting rem a inder.
mb89530a series 62 ds07-12547-6e please confirm the latest package dimension by following url. http://edevice.fujitsu.com/package/en-search/ (continued) 64-pin pl as tic lqfp le a d pitch 0.65 mm p a ck a ge width p a ck a ge length 12 12 mm le a d s h a pe g u llwing s e a ling method pl as tic mold mo u nting height 1.70 mm max code (reference) p-lqfp64-12 12-0.65 64-pin pl as tic lqfp (fpt-64p-m09) (fpt-64p-m09) c 200 3 -200 8 fujit s u microelectronic s limited f6401 8s -c- 3 -6 0.65(.026) 0.10(.004) 116 17 3 2 49 64 33 4 8 12.000.10(.472.004) s q 14.000.20(.551.00 8 ) s q index 0. 3 20.05 (.01 3 .002) m 0.1 3 (.005) 0.1450.055 (.0057.0022) "a" .059 ?.004 +.00 8 ?0.10 +0.20 1.50 0~ 8 0.25(.010) (mo u nting height) 0.500.20 (.020.00 8 ) 0.600.15 (.024.006) 0.100.10 (.004.004) det a il s of "a" p a rt ( s t a nd off) 0.10(.004) * dimen s ion s in mm (inche s ). note: the v a l u e s in p a renthe s e s a re reference v a l u e s . note 1) * : the s e dimen s ion s do not incl u de re s in protr us ion. note 2) pin s width a nd pin s thickne ss incl u de pl a ting thickne ss . note 3 )pin s width do not incl u de tie ba r c u tting rem a inder.
mb89530a series ds07-12547-6e 63 please confirm the latest package dimension by following url. http://edevice.fujitsu.com/package/en-search/ (continued) 64-pin pl as tic bcc le a d pitch 0.50 mm p a ck a ge width p a ck a ge length 9.00 mm 9.00 mm s e a ling method pl as tic mold mo u nting height 0. 8 0 mm max weight 0.10g 64-pin pl as tic bcc (lcc-64p-m19) (lcc-64p-m19) c 2002 fujit s u limited c64019 s -c-1-1 1 17 49 33 0.500.10 (.020.004) 0.50(.020) typ 8 .10(. 3 19) typ 8 .20(. 3 2 3 ) typ "c" "b" "a" 7.00(.276)ref 7.00(.276) ref 0.500.10 (.020.004) 0.50(.020) typ 8 .10(. 3 19)typ 8 .20(. 3 2 3 )typ (0. 8 0(.0 3 1)max) 0.0750.025 (.00 3 .001) 17 33 49 1 9.000.10(. 3 54.004) ( s t a nd off) 9.000.10 (. 3 54.004) 0.05(.002) 0.550.06 (.022.002) 0.550.06 (.022.002) det a il s of "b" p a rt c0.2(.00 8 ) 0. 3 00.06 (.012.002) 0.700.06 (.02 8 .002) det a il s of "a" p a rt det a il s of "c" p a rt 0.550.06 (.022.002) 0.550.06 (.022.002) (mo u nt height) index area 8 .25(. 3 25)ref 8 .25(. 3 25) ref "a" (.024.002) 0.600.06 0. 3 00.06 (.012.002) 0.14(.006)min. ?2002-200 8 fujit s u microelectronic s limited c64019 s -c-1-2 dimen s ion s in mm (inche s ). note: the v a l u e s in p a renthe s e s a re reference v a l u e s .
mb89530a series 64 ds07-12547-6e please confirm the latest package dimension by following url. http://edevice.fujitsu.com/package/en-search/ (continued) 64-pin pl as tic bcc le a d pitch 0.50 mm p a ck a ge width p a ck a ge length 9.00 mm 9.00 mm s e a ling method pl as tic mold mo u nting height 0.80 mm max 64-pin pl as tic bcc (lcc-64p-m16) (lcc-64p-m16) c 2001-2008 fujit s u microelectronic s limited c64016 s -c-2-2 1 17 49 33 0.500.10 (.020.004) 0.50(.020) typ 7.00(.276) ref 8.15(.321) ref "c" "b" "a" 8.15(.321)ref 8.20(.323) typ 0.500.10 (.020.004) 0.50(.020) typ 7.00(.276)ref 8.20(.323)typ (0.80(.031)max) 0.0750.025 (.003.001) 17 33 49 1 9.000.10(.354.004) ( s t a nd off) 9.000.10 (.354.004) 0.05(.002) det a il s of "c" p a rt 0.450.06 (.018.002) 0.450.06 (.018.002) (mo u nt height) index area det a il s of "a" p a rt (.016.002) 0.400.06 (.012.002) 0.300.06 c0.2(.008) det a il s of "b" p a rt (.018.002) 0.450.06 (.018.002) 0.450.06 0.14(.006) min dimen s ion s in mm (inche s ). note: the v a l u e s in p a renthe s e s a re reference v a l u e s .
mb89530a series ds07-12547-6e 65 please confirm the latest package dimension by following url. http://edevice.fujitsu.com/package/en-search/ (continued) 64-pin cer a mic mdip le a d pitch 1.778mm (70mil) row s p a cing 19.05mm (750mil) mother b o a rd m a teri a l cer a mic mo u nted p a cking m a teri a l pl as tic 64-pin cer a mic mdip (mdp-64c-p02) (mdp-64c-p02) +0.13 ?0.08 +.005 ?.003 index area 0~9 (.750.012) 19.050.30 0.46 .018 (2.240.025) (.010.002) 0.250.05 (.050.010) 1.270.25 (.135.015) 3.430.38 55.12(2.170)ref (.035.005) 0.900.13 (.070.010) 1.7780.25 10.16(.400)max 33.02(1.300)ref (.100.010) 2.540.25 (.738.012) 18.750.30 typ 15.24(.600) 56.900.64 1994-2008 fujit s u microelectronic s limited m64002 s c-1-5 c dimen s ion s in mm (inche s ). note: the v a l u e s in p a renthe s e s a re reference v a l u e s .
mb89530a series 66 ds07-12547-6e (continued) please confirm the latest package dimension by following url. http://edevice.fujitsu.com/package/en-search/ 64-pin cer a mic mqfp le a d pitch 1.00 mm le a d s h a pe s tr a ight mother b o a rd m a teri a l cer a mic mo u nted p a ck a ge m a teri a l pl as tic 64-pin cer a mic mqfp (mqp-64c-p01) (mqp-64c-p01) c 1994-200 8 fujit s u microelectronic s limited m64004 s c-1-4 15.5 8 0.20 (.61 3 .00 8 ) 16. 3 00. 33 (.642.01 3 ) 1 8 .70(.7 3 6)typ index area 0. 3 0(.012) typ 1.270.1 3 (.050.005) 22. 3 00. 33 (. 8 7 8 .01 3 ) 24.70(.972) typ 10.16(.400) typ 12.02(.47 3 ) typ 14.22(.560) typ 1 8 .120.20 (.71 3 .00 8 ) 1.270.1 3 (.050.005) 0. 3 0(.012)typ 7.62(. 3 00)typ 9.4 8 (. 3 7 3 )typ 11.6 8 (.460)typ 0.50(.020)typ 0.150.05 (.006.002) 10. 8 2(.426) max 0.400.10 (.016.004) .047 e.00 8 +.016 e0.20 +0.40 1.20 0.400.10 (.016.004) 1.000.25 (.0 3 9.010) 1 8 .00(.709) typ 1.000.25 (.0 3 9.010) 12.00(.472)typ .047 e.00 8 +.016 e0.20 +0.40 1.20 dimen s ion s in mm (inche s ). note: the v a l u e s in p a renthe s e s a re reference v a l u e s .
mb89530a series ds07-12547-6e 67 main changes in this edition the vertical lines marked in the left side of the p age show the changes. page section change results 38 electrical characteristics 3. dc characteristics (1) supply voltage at 5.0 (v) added the item ?pull-down resistance?. 39 added the table footnote ?*2? 41 (2) supply voltage at 3.0 (v) (except mb89 f538) added the item ?pull-down resistance?.
mb89530a series fujitsu microelectronics limited 7-1, nishishinjuku 2-chome, shinjuku dai-ichi seimei bldg., shinjuku-ku, tokyo 163-0722, japan tel: +81-3-5322-3347 fax: +81-3-5322-3387 http://jp.fujitsu.com/fml/en/ for further information please contact: north and south america fujitsu microelectronics america, inc. 1250 e. arques avenue, m/s 333 sunnyvale, ca 94085-5401, u.s.a. tel: +1-408-737-5600 fax: +1-408-737-5999 http://www.fma.fujitsu.com/ europe fujitsu microelectronics europe gmbh pittlerstrasse 47, 63225 langen, f. r. germany tel: +49-6103-690-0 fax: +49-6103-690-122 http://emea.fujitsu.com/microelectronics/ korea fujitsu microelectronics korea ltd. 1002 daechi-dong, 206 kosmo tower, kangnam-gu, seoul 135-280, korea tel: +82-2-3484-7100 fax: +82-2-3484-7111 http://www.fmk.fujitsu.com/ asia pacific fujitsu microelectronics asia pte ltd. 151 lorong chuan, #05-08 new tech park, singapore 556741, singapore tel: +65-6281-0770 fax: +65-6281-0220 http://www.fujitsu.com/sg/serv ices/micro/semiconductor/ fujitsu microelectronics shanghai co., ltd. no.222 yan an road(e), rm.3102, bund center, shanghai 200002, p. r. china tel: +86-21-6335-1560 fax: +86-21-6335-1605 http://cn.fujitsu.com/fmc/ fujitsu microelectronics pacific asia ltd. 11 canton road, 10/f., world commerce centre, tsimshatsui, kowloon, hong kong tel: +852-2377-0226 fax: +852-2376-3269 http://cn.fujitsu.com/fmc/tw all rights reserved. the contents of this document are subject to change without notice. customers are advised to consult with sales representatives before ordering. the information, such as descriptions of f unction and application circuit examples, in this document are presented solely for t he purpose of reference to show examples of operations and uses of fujitsu microelectronics device; fujitsu microelectronics does not warrant proper operation of the device with respect to us e based on such information. wh en you develop equipment incor porat- ing the device based on such information, you must assume any responsibility arising out of su ch use of the information. fujitsu microelectronics assumes no liability for any damages whatsoever arising out of the use of the information. any information in this document, including descriptions of f unction and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of fujitsu microelectroni cs or any third party or does fujitsu microelectronics warrant non-i nfringement of any third-party's intellectual property right o r other right by using such information. fujitsu microelectronics assumes no liability for any infringement of the intellectual property rights or other rights of third parties which w ould result from the use of information contained herein. the products described in this document are designed, developed and manufactured as contemplated for general use, including wit hout limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and m anufactured as contemplated (1) for use accompanying fata l risks or dangers that, unless extremely hi gh safety is secured, could have a ser ious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport contro l, medical life support system, missile la unch control in weapon system), or (2) for use requiring extremely high reliab ility (i.e., submersible repeater and artificial satellite). please note that fujitsu microelectronics will not be liable against you and/or any third party for any claims or damages arisi ng in connection with above-mentioned uses of the products. any semiconductor devices have an inherent chance of failure. you must protect against injury, damage or loss from such failure s by incorporating safety design measures into your facility and equi pment such as redundancy, fire protection, and prevention of ov er-current levels and other abnormal operating conditions. exportation/release of any products described in this document may require necessary procedures in accordance with the regulati ons of the foreign exchange and foreign trade control law of japan and/or us export control laws. the company names and brand names herein are the trademarks or registered trademarks of their respective owners. edited business & media promotion dept.

▲Up To Search▲

Price & Availability of MB89PV530C-201

	To Download MB89PV530C-201 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .